Stormoprene

Part B Activator to be used with Stormoprene Hypalon Part A Contact Adhesive (A3707).

Part B Activator to be used with Stormoprene Hypalon Part A Contact Adhesive (A3707).

A general use adhesive in a fairly large tube. Now comes in stackable box with hang tab for retail display. Works on most materials like leather, wood, PVC, PU, Latex, etc. Widely used in the manufacturing and repair of shoes and footwear, waterproof and airtight items such as large inflatable boats (RIBS) and also felt wader soles.

This is the same high strength quick drying impact adhesive as used in the 2 part set. It can be used very effectively on most material as a single part.
You must mix with the part B for sticking Hypalon.

Perfect alternative to Evo-Stik 8000.

This adheive is a conact adhesive: spread on to each of the sides to be stuck together and leave for 5 minutes until touch dry. Then press firmly together.

You can use just the glue (as a single component glue) on many fabrics, but the activator must be mixed with the adhesive when used to stick Hypalon fabric.

The glue is water proof and often used for making and repairing inflatable boats, RIBS and other marine craft.

These tins cannot be sent by Air Mail. It has to go by courier if you live outside the United Kingdom.

Choose Item SP70 instead.

Perfect alternative to Evo-Stik 8000.

This is a 5 litre tin of Stormoprene contact adhesive, and it comes with a 200ml bottle of activator. This adhesive is a contact adhesive: spread on to each of the sides to be stuck together and leave for 5 minutes until touch dry. Then press the two sides firmly together.

You can use just the glue (as a single component glue) on many fabrics, but the activator must be mixed with the adhesive when used to stick Hypalon fabric.

This adhesive is ideal for use on outdoor jobs. It is waterproof and resistant to UV deterioration.

Perfect alternative to Evo-Stik 8000.

This kit contains all the components that you need to replace the bottleneck shaped wrist seal on a drysuit. Full instructions are on the pack. Make a good quality water tight repair at a fraction of the cost of sending the suit away for repair.

Stormsure Bottleneck Shaped Wrist Seal

High Quality Latex made in the UK

Size: Medium

Top Cone: 44mm diameter

Bottom Cone: 89mm diameter

Height: 120mm

Stormoprene Adhesive

Stormoprene Hypalon Adhesive is a specially formulated 2-part poly-chloroprene based adhesive system for high-performance bonding of Hypalon and other natural and synthetic rubber surfaces that require high strength bonds for use in demanding applications.

Formulated for use in the manufacture and repair of RIBs, inflatable boats, liferafts, diving suits, wet suits and other marine and industrial applications that specify resistance to salt water, oil, fuels etc. 

Directions:

1. Cut off the damaged seal, leaving the part of the suit where the factory seal is attached to the fabric. The new seal will be glued over the old factory seal edge.

2. Slide the new seal into the factory edge and put an elastic band or bungee around the suit to keep it in place. Slide some silicone/wax paper under the cut off edge to keep glue from sticking to the seal, or you can put wax on the seal.

3. Clean the edge of the suit and the new seal edge with solvent (the side with the stripes is the inside.) Gently sand paper it to roughen the surface. Do not let the seal stick out too far, as the small end of the seal should not be stretched over it. It might cause the new seal to slide out of position.

4. Slide the seal on over the factory rubber area. You can put elastic bands around to keep the new seal from sliding.

5. Roll back the new seal so that the 2cm edge that was over the old suit is now facing up. Apply a thin layer of Stormoprene Contact Adhesive to each side. Wait 5 minutes and apply a second layer of adhesive to each side. Use a spatula or knife to apply the glue. When the glue is touch dry, roll the new latex seal right into place over the rubber part of the old seal. It bonds instantly. Press firmly over the glue area to ensure full adhesion.

6. Take your time.

Remove old seal. Cut seal to fit if needed. Apply two layers of Stormoprene glue onto both the drysuit/wetsuit and the area of the seal that will be stuck to the drysuit/wetsuit. Position drysuit seal area so that the seal can be stuck on comfortably. Bond and allow to cure for 2 hours. Full instructions are included.

This kit contains all the components that you need to replace the neck seal on a drysuit. Full instructions are on the pack. Make a good quality water tight repair at a fraction of the cost of sending the suit away for repair.

Stormsure Neck Seal

High Quality Latex made in the UK

Size: Medium

Top Cone: 89mm diameter

Bottom Cone: 254mm diameter

Stormoprene Adhesive

Stormoprene Hypalon Adhesive is a specially formulated 2-part poly-chloroprene based adhesive system for high-performance bonding of Hypalon and other natural and synthetic rubber surfaces that require high strength bonds for use in demanding applications.

Formulated for use in the manufacture and repair of RIBs, inflatable boats, liferafts, diving suits, wet suits and other marine and industrial applications that specify resistance to salt water, oil, fuels etc. 

Directions:

1. Cut off the damaged seal, leaving the part of the suit where the factory seal is attached to the fabric. The new seal will be glued over the old factory seal edge.

2. Slide the new seal into the factory edge and put an elastic band or bungee around the suit to keep it in place. Slide some silicone/wax paper under the cut off edge to keep glue from sticking to the seal, or you can put wax on the seal.

3. Clean the edge of the suit and the new seal edge with solvent (the side with the stripes is the inside.) Gently sand paper it to roughen the surface. Do not let the seal stick out too far, as the small end of the seal should not be stretched over it. It might cause the new seal to slide out of position.

4. Slide the seal on over the factory rubber area. You can put elastic bands around to keep the new seal from sliding.

5. Roll back the new seal so that the 2cm edge that was over the old suit is now facing up. Apply a thin layer of Stormoprene Contact Adhesive to each side. Wait 5 minutes and apply a second layer of adhesive to each side. Use a spatula or knife to apply the glue. When the glue is touch dry, roll the new latex seal right into place over the rubber part of the old seal. It bonds instantly. Press firmly over the glue area to ensure full adhesion.

6. Take your time.